USER’S
REFERENCE
ADAPTEC SCSI CARD 39160
ULTRA160 SCSI CONTROLLER
▼ ▼ ▼ ▼
Adaptec SCSI Card 39160
Ultra160 SCSI Controller
User’s Reference
R
▼ ▼ ▼ ▼
Contents
Using the Adaptec SCSI Card 39160 and SCSI
Devices 11
Configuring the Adaptec SCSI Card 39160 with
SCSISelect 16
iii
Adaptec SCSI Card 39160 User’s Reference
iv
Overview
Ultra160 SCSI on the Adaptec SCSI Card 39160
The Adaptec SCSI Card 39160 enables you to connect up to 30 SCSI
devices—such as very large arrays of high-performance HDDs,
external storage subsystems, clustered configurations, Ultra160 hard
disk drives, scanners, and CD-ROM drives—to any Intel-based com-
puter with 64- or 32-bit PCI expansion slots. Ultra160 is a new gener-
ation of SCSI technology that increases SCSI performance from
80 MBytes/ sec to 160 MBytes/ sec. In addition to providing much
greater performance, Ultra160 SCSI enables a maximum allowable
cable length of 12 meters for optimal connectivity and flexibility.1
The Adaptec SCSI Card 39160 has two independent SCSI channels,
each with a maximum throughput of 160 MBytes/ sec.
■ SCSI Channel A (marked “CH 1/ A” on the card) has two
internal connectors and one external connector.
■ SCSI Channel B (marked “CH 2/ B” on the card) has one inter-
nal connector and one external connector.
For the best data I/ O performance, connect only LVD (Low Voltage
Differential) devices and LVD cables to the Adaptec SCSI Card
39160. (LVD devices means Ultra160 and Ultra2 SCSI devices.) If you
connect non-LVD devices (for example, Fast SCSI or Ultra SCSI
devices), we recommend that you connect them to SCSI Channel A.
This allows you to operate Ultra160 and Ultra2 devices at their max-
1
When only one Ultra2 or Ultra160 SCSI device is connected, the cable length
can be up to 25 meters (82 feet).
1
Adaptec SCSI Card 39160 User’s Reference
imum speed on Channel B while at the same time using non-LVD
SCSI devices on Channel A.
Although the Adaptec SCSI Card 39160 is a 64-bit PCI card, it also
works in a 32-bit PCI slot. When installed in a 32-bit PCI slot, the
card automatically runs in the slower 32-bit mode.
This User’s Reference provides information about troubleshooting,
SCSI termination, and other important topics. It also explains how to
use the built-in SCSISelect utility if you need to change the Adaptec
SCSI Card 39160 settings.
Note: Read the Adaptec SCSI Card 39160 Installation Guide if
you need instructions on installing the SCSI Card and con-
necting SCSI devices to it.
Understanding SCSI
SCSI (pronounced “scuzzy”) stands for Small Computer Systems
Interface. SCSI is an industry standard computer interface for con-
necting SCSI devices (such as a hard disk drive, CD-ROM drive, or
scanner) to a common SCSI bus.
A SCSI bus is an electrical pathway that consists of a SCSI adapter
card (such as the Adaptec SCSI Card 39160) installed in a computer
and one or more SCSI devices. SCSI cables are used to connect the
devices to the SCSI adapter card. The Adaptec SCSI Card 39160 has
two independent SCSI buses (channels).
For the SCSI bus to function properly, a unique SCSI ID must be
assigned to the SCSI card and each SCSI device connected to it, and
the SCSI bus must be properly terminated.
2
Overview
SCSI IDs
Each device attached to the Adaptec SCSI Card 39160, as well as the
Adaptec SCSI Card 39160 itself, must be assigned a unique SCSI ID
number from 0 to 15 for each of the two SCSI buses. A SCSI ID
uniquely identifies each SCSI device on the SCSI bus and determines
priority when two or more devices are trying to use the SCSI bus at
the same time.
Refer to the device’s documentation to set the SCSI ID. Here are
some general guidelines for SCSI IDs:
■ For internal SCSI devices, the SCSI ID usually is set by config-
uring a jumper on the device.
■ For external SCSI devices, the SCSI ID usually is set with a
switch on the back of the device.
■ SCSI ID numbers do not need to be sequential, as long as the
Adaptec SCSI Card 39160 and each device has a different num-
ber. For example, on each of the two SCSI buses you can have
an internal SCSI device with ID 0, and an external SCSI device
with ID 6.
■ SCSI ID 7 has the highest priority on the SCSI bus. The priority
of the remaining IDs, in descending order, is 6 to 0, then 15 to 8.
■ On both SCSI buses (channels) the Adaptec SCSI Card 39160 is
preset to SCSI ID 7 and should not be changed. This gives the
card the highest priority on the SCSI bus.
■ Most internal SCSI hard disk drives come from the factory pre-
set to SCSI ID 0.
■ If you have 8-bit (or Narrow) SCSI devices, they must use SCSI
IDs 0, 1, 2, 3, 4, 5, or 6. SCSI ID 0 is recommended for the first
SCSI hard disk drive.
■ If you are booting your computer from a SCSI hard disk drive
connected to the Adaptec SCSI Card 39160, the Boot SCSI ID
setting in the SCSISelect utility must correspond to the SCSI ID
of the device from which you are booting. By default, the Boot
SCSI ID is set to 0. We recommend that you do not change this
setting.
■ In Windows® 95/ 98, you can use the Device Manager to deter-
mine which SCSI ID is assigned to each installed SCSI device.
3
Adaptec SCSI Card 39160 User’s Reference
Terminating the SCSI Bus
To ensure reliable communication on the SCSI bus, the ends of the
SCSI bus must be properly terminated. This is accomplished when
the device at the end of each cable, or the end of the cable itself, has a
terminator installed (or enabled). Terminators must be removed, or
termination must be disabled, on devices between the ends of each
cable.
Since the method for terminating a SCSI device can vary widely,
refer to the device’s documentation for instructions on how to
enable or disable termination. Here are some general guidelines for
termination:
■ Internal Ultra160 and Ultra2 SCSI devices come from the fac-
tory with termination disabled and cannot be changed. Proper
termination for these internal devices is provided by the built-
in terminator at the end of the 68-pin internal LVD SCSI cable.
■ Termination on Wide SCSI, Narrow SCSI, and Ultra SCSI
devices usually is controlled by manually setting a jumper or a
switch on the device, or by physically removing or installing
one or more resistor modules on the device.
■ Termination on most external SCSI devices is controlled by
installing or removing a SCSI terminator. However, termina-
tion on some external SCSI devices is enabled or disabled by
setting a switch on the back of the SCSI device.
■ By default, termination on the Adaptec SCSI Card 39160 itself
is set to Automatic (the preferred method). We recommend that
you do not change this default setting.
4
Troubleshooting
Troubleshooting
Most problems can be resolved by following the recommendations
in the Troubleshooting Checklist below. If you still experience prob-
lems after following the recommendations, continue with the rest of
this section.
Troubleshooting Checklist
Most problems with using the Adaptec SCSI Card 39160 result from
errors in preparing and connecting devices on the SCSI bus. If you
have problems, check these items first.
Note: If you have problems with a specific SCSI device when
other connected SCSI devices are working correctly, please
contact the manufacturer of the problem device for trouble-
shooting information.
■ Are all SCSI cables and power cables properly connected?
■ Are all SCSI devices turned on?
■ Have you connected SCSI devices to no more than two of the
three SCSI Channel A connectors? If you connected devices to
all three connectors, disconnect devices from one connector!
■ Is the Adaptec SCSI Card 39160 firmly seated and secured in
the PCI expansion slot?
■ Is the PCI expansion slot compliant with PCI Rev. 2.1 or higher,
and does it support Bus Mastering?
■ Are all SCSI devices on each SCSI bus assigned unique SCSI
IDs?
■ Are all SCSI devices terminated properly?
5
Adaptec SCSI Card 39160 User’s Reference
Troubleshooting in Windows 95/98
When I start Windows 95/98, the system locks up when the Windows
logo is displayed. How can I get the system to start so that I can verify
that the SCSI card is functioning normally?
1
2
Start or restart your computer.
(For Windows 95:) When the message “Starting Windows 95”
appears, press and release the F8 function key while the text is
on your screen.
(For Windows 98:) When the message “Starting Windows 98”
appears, press and release the Ctrl key while the text is on your
screen.
3
4
From the menu that is displayed, select Safe Mode. (It may
take several minutes for Windows 95/ 98 to load.)
If the system completes the boot to the desktop, the core soft-
ware is functional; resources, software conflicts, and/ or hard-
ware need to be checked.
5
If the system still fails to boot, and the boot drive is connected
to an EIDE controller, shut down the system, remove the
Adaptec SCSI Card 39160, and restart the computer.
6
7
Verify that an IRQ is available by viewing resources in System
Properties.
Under the Control Panel, verify that the operating system is set
to Optimal Performance by checking the Performance tab
under System Properties. (Make sure you are not in Safe
Mode.)
How can I tell if the Adaptec SCSI Card 39160 driver is loading
properly?
1
Right click on the My Computer icon on the Windows
desktop.
2
3
Select Properties from the menu.
Click the Device Manager tab.
6
Troubleshooting
4
Double-click the SCSI Controller icon. The software driver for
the Adaptec SCSI Card 39160 is listed as 29160(N), 39160,
AHA-3960D, AIC-7892/7899 Ultra160 PCI SCSI Controller.
■
If the driver is listed, the Adaptec SCSI Card 39160 driver is
loading properly.
■
If the driver is listed but has an exclamation mark inside a
yellow circle the software driver may conflict with other
hardware using the same resources. Double-click the icon
to see the device status and possible solutions.
■
■
If the driver is listed but has an “X” inside a red circle, the
Adaptec SCSI Card 39160 software driver is disabled and
isn’t loading.
If the SCSI Controller icon or the Adaptec SCSI Card 39160
software driver is not listed, reinstall the driver. (For
instructions on how to do this, refer to the Ultra160 Family
Manager Set User’s Guide.)
An “X” inside a red circle appears with the Adaptec SCSI Card 39160
software driver in Device Manager. What does this mean?
It means that the Adaptec SCSI Card 39160 software driver is dis-
abled and isn’t loading.
To enable the driver
1
Double-click the Adaptec SCSI Card 39160 software driver in
Device Manager.
2
Under the General tab, click the Original Configuration (cur-
rent) box.
What if there is no SCSI Controller icon under Device Manager, or the
software driver for the Adaptec SCSI Card 39160 does not appear
under Device Manager?
If the SCSI Controller icon or the software driver do not appear
1
2
3
Double-click the Add New Hardware icon in Control Panel.
Click Next to begin installing your new hardware.
Select Yes (recommended) and click Next to have Windows
search for the Adaptec SCSI Card 39160.
4
Follow the on-screen instructions.
7
Adaptec SCSI Card 39160 User’s Reference
If Windows 95/ 98 does not detect the Adaptec SCSI Card 39160, get
the driver disk or CD included with the SCSI card and run the Add
New Hardware wizard again:
1
2
3
Double-click the Add New Hardware icon in Control Panel.
Click Next to begin installing your new hardware.
Select No and click Next to select the type of hardware you
want to install.
4
Select SCSI controllers and click Next.
Note: The 39160 will not appear on the Models list
when Adaptec is selected from the Manufacturers list.
5
6
Click Have Disk... and follow the directions that appear on the
screen to install the driver software.
Select 29160(N), 39160, AHA-3960D, AIC-7892/7899 Ultra160
PCI SCSI Controller.
How can I check the status of a resource such as IRQ, Memory, or I/O?
1
2
3
4
5
Right click on My Computer.
Select Properties from the menu.
Click the Device Manager tab.
Double-click the Computer icon.
On the View Resources tab, click the option button for the type
of resource you want to check:
■
■
■
■
Interrupt Request (IRQ)
Input/ Output Address (I/ O)
Direct Memory Access (DMA)
Memory
6
The setting and the hardware using the setting are displayed.
■
If a specific resource is not listed, the resource is not used
by a device.
8
Troubleshooting
■
■
If a resource is listed more than once, the resource is used
by more than one device.
If a resource is used by an unknown device, the resource is
used but the device using the resource cannot be detected.
(This condition is most common.)
7
Click Cancel to close the windows, then close Control Panel.
How do I use the Hardware Conflict Troubleshooter in Windows 95/98?
1
2
Click the Start button, then click Help.
From the Contents tab, double-click Troubleshooting. (In
Windows 98, click Troubleshooting and then click Windows
98 Troubleshooting.)
3
4
Double-click if you have a hardware conflict.
Follow the step-by-step instructions in Windows Help.
9
Adaptec SCSI Card 39160 User’s Reference
Common Error Messages
Here is what you should do if the following messages appear on the
screen at bootup:
“Device connected, but not ready”
The host computer received no answer when it requested data from
an installed SCSI device.
1
Run SCSISelect® and set the Send Start Unit Command to Yes
2
Ensure that the device is set to spin up when the power is
switched on. The spin up option is typically set by a jumper.
(See the documentation for the device.)
“Start unit request failed”
The SCSI card BIOS was unable to send a Start Unit Command to
one of the installed SCSI devices. Run SCSISelect and disable the
Send Start Unit Command for the device.
“Time-out failure during...”
An unexpected time-out occurred.
1
2
Verify that the SCSI bus is properly terminated.
Verify that all cables are properly connected.
Try disconnecting the SCSI device cables from the SCSI card and
then starting the computer. If the computer successfully restarts, one
of the SCSI devices may be defective.
10
Using the Adaptec SCSI Card 39160 and SCSI Devices
Using the Adaptec SCSI
Card 39160 and SCSI
Devices
This section provides useful information on using the Adaptec SCSI
Card 39160 and your SCSI devices. For more information about a
specific SCSI device, refer to the documentation for that device.
Using SCSI Devices
Caution: Do not connect SCSI devices to more than two of
the three SCSI Channel A connectors at the same time.
Using SCSI Hard Disk Drives
■ If you connect a SCSI hard disk drive to the Adaptec SCSI Card
39160 that was previously connected to a different SCSI card,
you must low-level format the drive before you can use it. Back
format utility.)
Caution: A low-level format destroys all data on the
drive. Be sure to back up the data before performing a
low-level format.
■ Every SCSI hard disk drive must be physically low-level for-
matted, partitioned, and logically formatted before it can be
used to store data. Most SCSI drives are pre-formatted at the
factory. If your SCSI hard disk drive has not been pre-format-
ted at the factory, and if your computer is running under DOS,
Windows® 3.x, or Windows 95/ 98, you can format the disk
with the DOS Fdisk and Format commands. (See the DOS and
Windows documentation for more information.) To format
11
Adaptec SCSI Card 39160 User’s Reference
SCSI hard disk drives running under other operating systems,
see the operating system documentation.
Using Ultra160 Hard Disk Drives
■ We recommend that you connect your LVD (Ultra160 and
Ultra2) SCSI devices to SCSI Channel B and your non-LVD
SCSI devices (if any) to SCSI Channel A. This allows the LVD
SCSI devices to run at their maximum performance levels of
160 MBytes/ sec or 80 MBytes/ sec. Or you can connect LVD
SCSI devices to both SCSI channels. If you combine LVD and
non-LVD SCSI devices on the same SCSI channel, the data
transfer rate of the LVD SCSI devices will drop down to non-
LVD SCSI performance levels of up to 40 MBytes/ sec.
68-pin internal LVD/SE 68-pin internal LVD/SE
connector Channel B
connector Channel A
68-pin external
LVD/SE connector
Channel A
Narrow
connector
Channel A
68-pin external
LVD/SE connector
Channel B
■ Internal Ultra2 and Ultra160 SCSI devices come from the fac-
tory with termination disabled and cannot be changed. Proper
termination is provided by the terminator at the end of the
internal LVD SCSI cable.
Using Scanners
If you connect a scanner to the Adaptec SCSI Card 39160, you must
install the scanner manufacturer ’s proprietary software drivers. See
your scanner ’s documentation for details.
12
Using the Adaptec SCSI Card 39160 and SCSI Devices
Combining SCSI and Non-SCSI Devices
You can install the Adaptec SCSI Card 39160 in a computer that
already has a non-SCSI controller, such as an EIDE controller. How-
ever, you cannot cross-connect the disk drives and other devices:
SCSI devices must be connected to the Adaptec SCSI Card 39160,
EIDE devices must be connected to the EIDE controller, and so on.
When you install the Adaptec SCSI Card 39160 and SCSI disk drives
in a computer that boots from a non-SCSI disk drive, the computer
will continue to boot from the non-SCSI disk drive unless you
change the computer’s CMOS configuration. You do not need to
change the configuration if you just want to use the SCSI drives for
additional file storage space.
If your computer ’s motherboard BIOS supports the BIOS Boot Spec-
ification (BBS) feature, you can select a different boot device without
much difficulty. (To determine if the motherboard BIOS supports
BBS, read the computer documentation or contact your mother-
board manufacturer.)
The following table shows what to do, after you physically install
the SCSI card and SCSI devices, to use different kinds of disk drives
in the same computer:
Does computer BIOS Want computer to boot
support BBS?
from SCSI drive?
Then do this:
No
No
No action required. SCSI drives
and non-SCSI drives can be used
together.
No
Yes
Run CMOS Setup program.
Change primary Hard Disk set-
ting to None or No Drives
Installed (see computer docu-
mentation). You will not be able to
use the non-SCSI drive(s) at all
when you boot from the SCSI
drive.
Yes
Yes
No
Yes
No action required. SCSI drives
and non-SCSI drives can be used
together.
Run CMOS Setup program and
select SCSI drive as boot device.
SCSI drives and non-SCSI drives
can be used together.
13
Adaptec SCSI Card 39160 User’s Reference
Installing Multiple SCSI Cards
■ You can install multiple SCSI cards in your computer; you are
limited only by the available system resources (for example,
IRQ settings, I/ O port addresses, BIOS addresses, and so
forth).
■ Each SCSI card you install forms a separate SCSI bus with a
different set of SCSI devices. SCSI IDs can be reused as long as
the ID is assigned to a device on a different SCSI card (for
example, each SCSI card can have a device with SCSI ID 2).
■ If you have two or more SCSI cards and your computer boots
from a SCSI disk drive, leave the host adapter BIOS enabled on
the SCSI card to which the boot disk drive is connected. Use
SCSISelect to disable the host adapter BIOS on the other SCSI
cards.
Connecting the LED Connector
(Optional feature) Most computers have an LED disk activity light on
the front panel of the system case. If you choose to disconnect the
cable from the LED connector on the motherboard and connect it to
the LED connector on the SCSI card as shown in the diagram below,
the LED on the front panel of the computer will light whenever
there is activity on the SCSI bus.
Note: If you connect the LED cable to the SCSI card, the LED
disk activity light will no longer indicate disk activity on the
non-SCSI disk drives.
LED Cable
from
motherboard
2-pin
LED
Cable
LED Connector
on host adapter
1
1
Pin 1
14
Using the Adaptec SCSI Card 39160 and SCSI Devices
Overriding SCSI Termination Settings
You use SCSISelect to control the termination of the two SCSI chan-
nels on the Adaptec SCSI Card 39160. The default termination set-
ting for both channels is Automatic. This setting allows the SCSI card
to adjust SCSI termination automatically, depending on which con-
nectors have SCSI devices attached to them.
Regardless of the SCSISelect termination setting, the SCSI card termi-
nation is always disabled when the power is turned off. If you want
SCSI card termination to be enabled when the power is turned off,
you must terminate the SCSI channels manually.
To manually terminate Channel A, place a shunt on jumper J5. To
manually terminate Channel B, place a shunt on jumper J3. The fol-
lowing diagram shows where the jumpers are located on the SCSI
card:
J3
J5
You might want to manually terminate the SCSI card if the Adaptec
SCSI Card 39160 is connected to one or more external SCSI devices
that are also connected to a SCSI card in another computer. The
devices can be shared between the two computers if one SCSI card is
terminated when it is powered off, while the computer with the
other SCSI card is using the SCSI devices.
15
Adaptec SCSI Card 39160 User’s Reference
Configuring the Adaptec
SCSI Card 39160 with
Select
SCSI
SCSISelect, which is included with the Adaptec SCSI Card 39160,
enables you to change SCSI settings without opening the computer
or handling the card. SCSISelect also enables you to low-level format
or verify the disk media of your SCSI hard disk drives. The follow-
ing table lists the available and default settings for each SCSISelect
option. The settings marked as “Auto-sync” are automatically syn-
chronized for both SCSI channels—for example, if you change the
Boot Channel option to B First on Channel A, the change will apply
to Channel B as well. All other options can be set separately for each
of the two SCSI channels.
The default settings are appropriate for most systems and should
not be changed. Run SCSISelect if you need to change or view cur-
rent settings, or if you need to use the SCSI disk utilities. See the
SCSISelect Options
Available Settings
Default Setting
SCSI Bus Interface Definitions:
Host Adapter SCSI ID
SCSI Parity Checking
0-15
7
Enabled
Disabled
Enabled
Host Adapter SCSI Termination:
Ch. A Automatic
Automatic
Automatic
Low On/ High On
Low Off/ High Off
Low Off/ High On
Ch. B Automatic,
Enabled, Disabled
Boot Device Options:
Boot Channel [Auto-sync]
Boot SCSI ID [Auto-sync]
A First, B First
A First
0-15
0-7
0
0
1
Boot LUN Number [Auto-sync]
16
Configuring the Adaptec SCSI Card 39160 with SCSISelect
SCSISelect Options
Available Settings
Default Setting
SCSI Device Configuration:
Sync Transfer Rate (MBytes/ sec)
160, 80.0, 53.4, 40.0, 160
32.0, 26.8, 20.0,
16.0, 13.4, 10.0,
ASYN
Initiate Wide Negotiation
Enable Disconnection
Yes, No
Yes, No
Yes, No
Yes, No,
Yes (Enabled)
Yes (Enabled)
Yes (Enabled)
N/ C (No
Send Start Unit Command
2
Enable Write Back Cache
N/ C (No Change) Change)
BIOS Multiple LUN Support
Yes, No
Yes, No
No (Disabled)
Yes (Enabled)
Include in BIOS Scan
Advanced Configuration Options:
Reset SCSI Bus at IC Initialization
Enabled, Disabled Enabled
Display <Ctrl> <A> Messages during Enabled, Disabled Enabled
BIOS Initialization [Auto-sync]
Extended BIOS Translation for
DOS Drives > 1 GByte
Enabled, Disabled Enabled
Verbose/ Silent Mode [Auto-sync]
Host Adapter BIOS [Auto-sync]
Verbose, Silent
Verbose
Enabled
Enabled
Disabled: Scan Bus
Disabled: Not Scan
Enabled, Disabled Enabled
Disabled
Boot Only,
Support Removable Disks Under BIOS Disabled,
as Fixed Disks
All Disks
Enabled, Disabled Enabled
Enabled, Disabled Enabled
1
Setting is valid only if Multiple LUN Support is enabled.
Settings are valid only if host adapter BIOS is enabled.
2
17
Adaptec SCSI Card 39160 User’s Reference
Starting SCSISelect
Follow these steps to start SCSISelect:
1
Turn on or restart your system.
During the startup process, pay careful attention to the mes-
sages that appear on your screen.
2
When the following message appears on your screen, press the
Ctrl-A keys simultaneously (this message appears for only a
few seconds):
Press <Ctrl><A> for SCSISelect (TM) Utility!
3
4
Select SCSI Channel A or B. Most SCSISelect options can be set
separately for each SCSI channel.
From the menu that appears, use the arrow keys to move the
cursor to the option you want to select, then press Enter.
Note: If you have difficulty viewing the display, press F5 to
toggle between color and monochrome modes. (This feature
may not work on some monitors.)
Exiting SCSISelect
Follow these steps to exit SCSISelect:
1
Press Esc until a message prompts you to exit (if you changed
any settings, you are prompted to save the changes before you
exit).
2
At the prompt, select Yes to exit, then press any key to reboot
the computer. Any changes you made in SCSISelect take effect
after the computer boots.
18
Configuring the Adaptec SCSI Card 39160 with SCSISelect
Using SCSISelect Settings
To select an option, use the arrow keys to move the cursor to the
option, then press Enter. In some cases, selecting an option displays
another menu. You can return to the previous menu at any time by
pressing Esc.
To restore the original SCSISelect default values, press F6 from the
main SCSISelect screen.
SCSI Bus Interface Definitions
■ Host Adapter SCSI ID—(Default: 7) Sets the SCSI ID for the
SCSI card. The Adaptec SCSI Card 39160 is set at 7, which
gives it the highest priority on the SCSI bus. We recommend
that you do not change this setting.
■ SCSI Parity Checking—(Default: Enabled) When set to
Enabled, verifies the accuracy of data transfer on the SCSI bus.
Leave this setting enabled unless any SCSI device connected to
the Adaptec SCSI Card 39160 does not support SCSI parity.
■ Host Adapter SCSI Termination—(Default: Automatic) Deter-
mines the termination setting for the SCSI card. The default
setting is Automatic, which allows the SCSI card to adjust the
termination as needed. We recommend that you do not change
this setting.
Boot Device Options
■ Boot Channel—(Default: A First) Specifies which of the two
SCSI channels the boot device is connected to (if the computer
boots from a SCSI device). If you change this setting, the
change automatically applies to both SCSI channels.
■ Boot SCSI ID—(Default: 0) Specifies the SCSI ID of your boot
device. We recommend that you do not change the default
setting. If you change this setting, the change automatically
applies to both SCSI channels.
■ Boot LUN Number—(Default: 0) Specifies which LUN (Logi-
cal Unit Number) to boot from on your boot device. This set-
ting is not valid unless Multiple LUN Support is enabled (see
setting, the change automatically applies to both SCSI
channels.
19
Adaptec SCSI Card 39160 User’s Reference
SCSI Device Configuration Options
SCSI Device Configuration options can be set individually for each
connected SCSI device.
Note: To configure settings for a SCSI device, you must
■ Sync Transfer Rate—(Default: 160) Determines the maximum
synchronous data transfer rate that the SCSI card supports. We
recommend that you leave the maximum (default) value of 160
MBytes/ sec.
■ Initiate Wide Negotiation—(Default: Yes) When set to Yes, the
SCSI card attempts 16-bit data transfer (wide negotiation).
When set to No, the SCSI card uses 8-bit data transfer unless
the SCSI device requests wide negotiation.
Note: Set Initiate Wide Negotiation to No if you are
using an 8-bit SCSI device that hangs or exhibits other
performance problems with 16-bit data transfer rate
enabled.
■ Enable Disconnection—(Default: Yes) When set to Yes, allows
the SCSI device to disconnect from the SCSI bus. Leave the set-
ting at Yes if two or more SCSI devices are connected to the
SCSI card. If only one SCSI device is connected, changing the
setting to No results in slightly better performance.
■ Send Start Unit Command—(Default: Yes) When set to Yes,
sends the Start Unit Command to the SCSI device at bootup.
The following three options have no effect if the SCSI Card BIOS is
disabled. (The SCSI Card BIOS is normally enabled by default.)
■ Enable Write Back Cache—(Default: N/C) Can be used to
enable or disable the write-back cache on SCSI disk drives con-
nected to the host adapter. Leave this option at its default
setting of N/ C (no change), which usually allows for optimum
drive performance.
20
Configuring the Adaptec SCSI Card 39160 with SCSISelect
■ BIOS Multiple LUN Support—(Default: No) Leave this set-
ting at No if the device does not have multiple Logical Unit
Numbers (LUNs). When set to Yes, the SCSI card BIOS pro-
vides boot support for a SCSI device with multiple LUNs (for
example, a CD “juke box” device in which multiple CDs can be
accessed simultaneously).
■ Include in BIOS Scan—(Default: Yes) When set to Yes, the
SCSI card BIOS includes the device as part of its BIOS scan at
bootup.
Advanced Configuration Options
Note: Do not change the Advanced Configuration Options
unless absolutely necessary.
■ Reset SCSI Bus at IC Initialization—(Default: Enabled) When
set to Enabled, the SCSI card generates a SCSI bus reset during
its power-on initialization and after a hard reset.
■ Display <Ctrl> <A> Messages during BIOS Initialization—
(Default: Enabled) When set to Enabled, the SCSI card BIOS
displays the Press <Ctrl> <A> for SCSISelect (TM) Utility! mes-
sage on your screen during system bootup. If this setting is dis-
abled, you can still invoke the SCSISelect Utility by pressing
<Ctrl> <A> after the SCSI card BIOS banner appears. If you
change this setting, the change automatically applies to both
SCSI channels.
■ Extended BIOS Translation for DOS Drives > 1 GByte—
(Default: Enabled) When set to Enabled, provides an extended
translation scheme for SCSI hard disks with capacities greater
than 1 GByte. This setting is necessary only for MS-DOS 5.0 or
above; it is not required for other operating systems, such as
NetWare or UNIX.
Caution: Changing the translation scheme destroys all
data on the drive. Be sure to back up your disk drives
before changing the translation scheme.
21
Adaptec SCSI Card 39160 User’s Reference
Use the MS-DOS Fdisk command to partition a disk larger
than 1 GByte controlled by the SCSI card BIOS, when using
DOS, Windows 3.1.x, or Windows 95/ 98.
■ Verbose/Silent Mode—(Default: Verbose) When set to Verbose,
the SCSI card BIOS displays the host adapter model on the
screen during system buildup. When set to Silent, the message
will not be displayed during bootup. If you change this setting,
the change automatically applies to both SCSI channels.
■ Host Adapter BIOS (Configuration Utility Reserves BIOS
Space)—(Default: Enabled) Enables or disables the SCSI card
BIOS. If you change this setting, the change automatically
applies to both SCSI channels.
■
Leave at Enabled to enable the SCSI card BIOS and allow it
to scan and initialize all SCSI devices.
■
Set to Disabled: Not scan if the devices on the SCSI bus (for
example, CD-ROM drives) are controlled by software driv-
ers and do not need the BIOS, and you do not want the
BIOS to scan the SCSI bus.
■
Set to Disabled: Scan Bus if you do not need the BIOS, but
you want it to scan the SCSI devices on the bus and you
need to spin up the device.
The following four options have no effect if the SCSI Card BIOS is
disabled. (The SCSI Card BIOS is normally enabled by default.)
■ Domain Validation—(Default: Enabled) Determines the opti-
mal transfer rate for each device on the SCSI bus and sets
transfer rates accordingly. Displays the resulting data transfer
rate. If you change this setting, the change automatically
applies to both SCSI channels.
■ Support Removable Disks Under BIOS as Fixed Disks—
(Default: Disabled) Determines which removable-media drives
are supported by the SCSI card BIOS. The options are as
follows:
■
Disabled— No removable-media drives are treated as hard
disk drives. Software drivers are required because the
drives are not controlled by the BIOS.
22
Configuring the Adaptec SCSI Card 39160 with SCSISelect
Caution: You may lose data if you remove a removable-
media cartridge from a SCSI drive controlled by the
SCSI card BIOS while the drive is on. If you want to be
able to remove the media while the drive is on, install
the removable-media software driver and set Support
Removable Disks Under BIOS as Fixed Disks to
Disabled.
■
■
Boot Only—Only the removable-media drive designated
as the boot device is treated as a hard disk drive.
All Disks—All removable-media drives supported by the
BIOS are treated as hard disk drives.
■ BIOS Support for Bootable CD-ROM—(Default: Enabled)
When set to Enabled, the SCSI card BIOS allows the computer
to boot from a CD-ROM drive.
■ BIOS Support for Int 13 Extensions—(Default: Enabled) When
set to Enabled, the SCSI card BIOS supports Int 13h extensions
as required by Plug-and-Play. The setting can be either enabled
or disabled if your system is not Plug-and-Play.
23
Adaptec SCSI Card 39160 User’s Reference
Using SCSI Disk Utilities
To access the SCSI disk utilities, follow these steps:
1
Select the SCSI Disk Utilities option from the menu that
appears after starting SCSISelect. SCSISelect scans the SCSI bus
(to determine the devices installed) and displays a list of all
SCSI IDs and the devices assigned to each ID.
2
3
Use the ↑ and ↓ keys to move the cursor to a specific ID and
device, then press Enter.
A small menu appears, displaying the options Format Disk
and Verify Disk Media.
■
Format Disk—Allows you to perform a low-level format
on a hard disk drive. Most SCSI disk devices are preformatted
at the factory and do not need to be formatted again.
Caution: A low-level format destroys all data on the
drive. Be sure to back up your data before performing
this operation. You cannot abort a low-level format
once it is started.
■
Verify Disk Media—Allows you to scan the media of a
hard disk drive for defects. If the utility finds bad blocks on
the media, it prompts you to reassign them; if you select
yes, those blocks are no longer used. You can press Esc at
any time to abort the utility.
24
Connecting SCSI Devices
Connecting SCSI Devices
Here are some examples of how you can connect internal and exter-
nal SCSI devices to the Adaptec SCSI Card 39160. To achieve maxi-
mum performance, attach the first device to the end connector of the
cable (furthest from the SCSI card); attach other devices to the con-
nectors that are closer to the SCSI card.
The first example shows Ultra160 and Ultra2 SCSI devices con-
nected to internal and external SCSI connectors of both SCSI
channels. Note the built-in terminators at the end of the internal
LVD SCSI cables. The last external SCSI device on each SCSI channel
must be terminated with an LVD/ SE terminator plug to ensure that
all devices will operate at their maximum speed.
Built-in
terminator
Built-in
terminator
T
T
T
T
Terminated
devices
Caution: Do not connect SCSI devices to more than two of
the three SCSI Channel A connectors at the same time.
The following example shows Ultra160 and Ultra2 SCSI devices con-
nected to the internal connectors of both SCSI channels.
Built-in
terminator
Built-in
terminator
T
T
25
Adaptec SCSI Card 39160 User’s Reference
The following example shows LVD (Ultra160 and Ultra2) SCSI
devices on Channel B and non-LVD SCSI devices on Channel A.
Ultra160 and Ultra2
SCSI devices
Non-LVD
SCSI devices
Built-in
terminator
T
T
T
T
Terminated
device
Terminated
devices
Maximum Cable Lengths
The total length of cabling (internal and external) on the SCSI bus
cannot exceed the maximum lengths listed in the following table.
The third column lists the maximum number of SCSI devices you
can connect to the SCSI card.
Maximum
Cable Length
Maximum Devices
Supported
Data Transfer Rate
25 m (82.0 ft) Ultra160 SCSI (160 MBytes/ sec)
and Ultra2 SCSI (80 MBytes/ sec)
1
1
12 m (39.4 ft) Ultra160 SCSI (160 MBytes/ sec)
15
and Ultra2 SCSI (80 MBytes/ sec)
3 m (9.8 ft)
3 m (9.8 ft)
3 m (9.8 ft)
Fast Wide SCSI (20 MBytes/ sec)
Fast SCSI (10 MBytes/ sec)
15
7
Ultra SCSI (40 MBytes/ sec for 16-
bit, 20 MBytes/ sec for 8-bit)
4
2
1.5 m (4.9 ft)
Ultra SCSI (40 MBytes/ sec for
16-bit, 20 MBytes/ sec for 8-bit)
5-7
1
2
Mixing Fast/ Ultra devices with Ultra160 and Ultra2 SCSI devices causes the entire
SCSI bus to default to Ultra SCSI speeds and cable length requirements.
Ultra SCSI data transfer rates do not currently support more than seven devices
connected to the SCSI card.
❒
26
Copyright
© 1999 Adaptec, Inc. All rights reserved. No part of this publication may be
reproduced, stored in a retrieval system, or transmitted in any form or by any means,
electronic, mechanical, photocopying, recording or otherwise, without the prior
written consent of Adaptec, Inc., 691 South Milpitas Blvd., Milpitas, CA 95035.
Trademarks
Adaptec, the Adaptec logo, AHA, SpeedFlex, and SCSISelect are trademarks of
Adaptec, Inc. which may be registered in some jurisdictions. Window and Windows
95/ 98 are registered trademarks of Microsoft Corporation in the U.S. and other
countries used under license. All other trademarks are owned by their respective
owners.
Changes
The material in this document is for information only and is subject to change
without notice. While reasonable efforts have been made in the preparation of this
document to assure its accuracy, Adaptec, Inc. assumes no liability resulting from
errors or omissions in this document, or from the use of the information contained
herein.
Adaptec reserves the right to make changes in the product design without reservation
and without notification to its users.
Disclaimer
IF THIS PRODUCT DIRECTS YOU TO COPY MATERIALS, YOU MUST HAVE
PERMISSION FROM THE COPYRIGHT OWNER OF THE MATERIALS TO AVOID
VIOLATING THE LAW WHICH COULD RESULT IN DAMAGES OR OTHER
REMEDIES.
27
Adaptec Customer Support
If you have questions about installing or using your Adaptec product, check this
User ’s Reference first—you will find answers to most of your questions here. If you
need further assistance, please contact us. We offer the following support and
information services.
Technical Support Identification (TSID) Number
■
The TSID is a 12-digit number that can be found on the white label included in
the box with your product. It helps to provide more efficient service to you by
accurately identifying your product and support status. The TSID is required
when you contact Technical Support.
■
Affix your TSID label here:
Contacting Support
Technical information including product literature, answers to commonly asked
questions, and information on software upgrades is available through the following:
■
For information about Adaptec’s support options, call 408-945-2550, 24 hours a
day, 7 days a week.
■
Search the Adaptec Support Knowledgebase (A.S.K.) at http:/ / ask.adaptec.com
for articles, troubleshooting tips, and frequently asked questions for your
product.
■
■
Connect to the File Transfer Protocol (FTP) server at ftp:/ / ftp.adaptec.com.
For email support, send technical questions to Adaptec’s Technical Support
■
■
To speak with a Technical Support Specialist, call 408-934-7274, Monday –Friday,
6:00 A.M. to 5:00 P.M., Pacific Time.
After-hours, weekend, and holiday support is available for a fee at 800-416-8066.
Sales and Ordering Information
■
■
For pre-sales assistance with Adaptec products; to place an order for software,
hardware, or cables; or to request additional documentation for Adaptec
products, call 800-442-7274 or 408-957-7274, Monday–Friday, 6:00 A.M. to 5:00
P.M., Pacific Time.
For sales information in Europe, call
■ France: +33 1 34 523434
■ Germany: +49 89 4564060
■ UK: +44 1276 854500
28
Regulatory Compliance Statements
Federal Communications Commission Radio Frequency Interference Statement
WARNING: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy, and if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. However, if this equipment
does cause interference to radio or television equipment reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/television technician for help.
• Use a shielded and properly grounded I/O cable and power cable to ensure compliance of this unit to the
specified limits of the rules.
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Adaptec, Inc. Adaptec SCSI Card 39160
Tested to Comply
With FCC Standards
FOR HOME OR OFFICE USE
European Union Compliance Statement
This Information Technology Equipment has been tested and found to comply with the
following European directives:
EMC Directive 89/ 336/ EEC
EN 50081-1 (1992):
EN55022 (1994) Class B
EN 50082-1 (1992):
EN61000-4-2 (1998)
EN61000-4-3 (1998)
EN61000-4-4 (1995)
Australian/New Zealand Compliance Statement
This device has been tested and found to comply with the limits for a Class B digital
device, pursuant to the Australian/ New Zealand standard AS/ NZS 3548 set out by the
Spectrum Management Agency.
29
Canadian Compliance Statement
This Class B digital apparatus meets all requirements of the Canadian Interference-
Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le
matérial brouilleur du Canada.
Japanese Compliance
30
Adaptec Software License Agreement
In return for acquiring a license to use the software (“Software”) and related documentation, you
agree to the following terms and conditions:
1
License: This Agreement grants you, the Licensee, a license to:
a
use the Software on a single computer system which incorporates an Adaptec SCSI Card,
or in the case of a multi-user or networked system which permits access to the Software by
more than one user at the same time, at a single working location.
b
make one copy of the Software in machine readable form solely for back-up purposes pro-
vided you reproduce Adaptec’s copyright notice and any proprietary legends.
2
Restrictions: You may not distribute copies of the Software to others or electronically transfer
the Software from one computer to another over a network. You may not use the Software
from multiple locations of a multi-user or networked system at any one time. The Software
contains trade secrets and in order to protect them you may not decompile, reverse engineer,
disassemble, or otherwise reduce the Software to a human-perceivable form. YOU MAY NOT
MODIFY, ADAPT, TRANSLATE, RENT, LEASE, LOAN, RESELL FOR PROFIT, DISTRIBUTE,
NETWORK OR CREATE DERIVATIVE WORKS BASED UPON THE SOFTWARE OR ANY
PART THEREOF.
3
Ownership of Software: As Licensee, you own the media upon which the software is fixed, but
Adaptec retains title and ownership of the Software recorded on the original media and all
subsequent copies of the Software regardless of the form or media in which or on which the
original and other copies may exist. This license is not a sale of the Software or any copy.
4
5
Confidentiality: You agree to maintain the Software in confidence and to not disclose the Soft-
ware to any third party without the express written consent of Adaptec. You further agree to
take all reasonable precautions to preclude access of unauthorized persons to the Software.
Term: This license is effective until January 1, 2042, unless terminated earlier. You may termi-
nate the license at any time by destroying the Software (including the related documentation)
together with all copies or modifications in any form. Adaptec will have the right to terminate
your license immediately if you fail to comply with any term or condition of this Agreement.
Upon any termination, including termination by you, you must destroy the Software (includ-
ing the related documentation) together with all copies or modifications in any form.
6
Limited Warranty: Adaptec warrants only that the media upon which the Software is fur-
nished will be free from defects in material or workmanship under normal use and service for
a period of thirty (30) days from the date of delivery to you. ADAPTEC DOES NOT AND
CANNOT WARRANT THE PERFORMANCE OR RESULTS YOU MAY OBTAIN BY USING
THE SOFTWARE OR DOCUMENTATION. THE FOREGOING STATES THE SOLE AND
EXCLUSIVE REMEDIES ADAPTEC WILL PROVIDE FOR BREACH OF WARRANTY.
EXCEPT FOR THE FOREGOING LIMITED WARRANTY, ADAPTEC MAKES NO WARRAN-
TIES, EXPRESS OR IMPLIED, AS TO NONINFRINGEMENT OF THIRD PARTY RIGHTS,
MERCHENTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not
allow the exclusion of implied warranties or limitations on how long an implied warranty may
last, so the above limitations may not apply to you. This warranty gives you specific legal
rights and you may also have other rights which vary from state to state.
7
8
Limitation of Liability: IN NO EVENT WILL ADAPTEC BE LIABLE TO YOU FOR ANY SPE-
CIAL DAMAGES, INCLUDING ANY LOST PROFITS, LOST SAVINGS OR OTHER INCI-
DENTAL OR CONSEQUENTIAL DAMAGES, EVEN IF ADAPTEC HAS BEEN ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES, OR FOR ANY CLAIM BY ANY OTHER PARTY.
Some states do not allow the exclusion or limitation of special, incidental, or consequential
damages, so the above limitation or exclusion may not apply to you.
Limitation of Remedies: Adaptec’s entire liability and your exclusive remedy shall be:
a
the replacement of any media not meeting Adaptec’s limited warranty which is returned to
Adaptec; or
b
if Adaptec or its distributor is unable to deliver replacement media which is free of defects
in materials or workmanship, you may terminate this Agreement by returning the Soft-
ware and your money will be refunded.
31
9
Export: You acknowledge that the laws and regulations of the United States restrict the export
and re-export of the Software. You agree that you will not export or re-export the Software or
media in any form without the appropriate United States and foreign government approval.
10 U.S. Government Restricted Rights Legend for Units of the DoD: Use, duplication or disclo-
sure by the Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of the
Rights in Technical Data and Computer Software clause at 252.227-7013. Adaptec, Inc., 691
South Milpitas Boulevard, Milpitas, California 95035.
11 U.S. Government Restricted Rights Legend for Civilian Agencies: Use, reproduction or disclo-
sure is subject to restrictions as set forth in subparagraphs (a) through (d) of the Commercial
Computer Software - Restricted Rights clause at 52.227-19 and the limitations set forth in
Adaptec, Inc.’s standard commercial agreement for this software. Unpublished - rights
reserved under the copyright laws of the United States.
12 General: You acknowledge that you have read this Agreement, understand it, and that by
opening the package you agree to be bound by its terms and conditions. You further agree that
it is the complete and exclusive statement of the agreement between Adaptec and you which
supersedes any proposal or prior agreement, oral or written, and any terms of this Agreement
or any different terms will be enforceable against Adaptec unless Adaptec gives its express
consent, including an express waiver of the terms of this Agreement, in a writing signed by an
officer of Adaptec. You assume full responsibility for the use of the Software and agree to use
the Software legally and responsibly. This Agreement shall be governed by California law
except as to copyright matters which are covered by Federal law. This Agreement is deemed
entered into at Milpitas, California by both parties. Should any provision of this Agreement be
declared unenforceable in any jurisdiction, then such provision shall be deemed to be sever-
able from this Agreement and shall not affect the remainder hereof. All rights in the Software
not specifically granted in this Agreement are reserved by Adaptec.
Should you have any questions concerning this Agreement, you may contact Adaptec by writing
to: Adaptec, Inc., Legal Department, 691 South Milpitas Boulevard, Milpitas, California 95035.
32
|